Digital multimeter. Measurement: DCV, ACV, DCA, ACA, Resistance, Capacitance, Frequency, Diode, Continuity beeper. A/D counts no.: 4000 counts. Range selection: auto range with manual range selecting. Zero adjustment: automatic. Sampling time: approx. 0.5 to 1 second. Operating temperature: 0°C to 50°C (32°F to 122°F). Operating humidity: Max. 80%RH. Power supply: 006 DC 9V battery. Power consumption: Approx. DC 1.7mA
Continuity buzzer: <20Ω ; Max Voltage 500V (DC) / 250V (AC rms)
Capacitance
40nF
0.01nF
±(3.0%reading+20digits), C<2nF
±(3.0%reading+1digits), C>2nF
400nF
0.1nF
4uF
0.001uF
40uF
0.01uF
100uF
0.1uF
Frequency (response 1.5V...5V)
4Hz
0.001Hz
±(0.5%reading+2digits)
40Hz
0.01Hz
400Hz
0.1Hz
4kHz
0.001kHz
40kHz
0.01kHz
400kHz
0.1kHz
4MHz
1kHz
Duty Cycle (10kHz max; 2...5V)
1...99%
0.1%
±(1.0%reading)
General specifications
Display: Large LCD (4000 counts), digits 23mm high. Range selection: Auto range with manual range selecting Data hold: To freeze the display reading on the LCD display Memory recall: Records Maximum & Minimum readings with recall Auto Power Off: this function can't be disabled Relative measurement: To offset the measurement value Polarity: Automatic Switching, "-" indicates negative polarity Zero adjustment: Automatic Sampling time: Approx. 0.5 to 1 second Input impedance: 10 M ohm. Operating temperature: 0°C to 50°C (32°F to 122°F) Operating humidity: Max. 80%RH. Power supply: 9V battery x 1 Power consumption: Approx. DC 1.7mA Dimensions: 7.3x3.5x1.6in/185x88x40mm Weight: 0.77lb/350g
Standard Accessories
Red and Black Test Leads (CAT III 1KV Test Leads)
0.5 Amp Spare Fuse
User Manual
Optional Accessories
Full line adapters: ACA/DCA current adapter, adapter, Tachometer adapter, Humidity adapter, Pressure adapter, Light adapter, EMF adapter, Sound level adapter, High voltage probe
Soft carrying case
AM-1061 Professional Digital Multimeter - rear view
Front panel covers LCD, button board, rotary function switch gear and main plated circuit board:
*Rubber strip between the back and front chassis covers protects from water and dust.
Protective fuses are mounted near the inputs and sound buzzer is placed behind the LCD.
*There is also an extra fuse fixed at the buttom (for several models) Up
How to replace or install the batteries?
When the batteries become exhausted or drop below the operating voltage, “BAT” indicator will appear in the LCD display. In this case the battery should be replaced, however in-spec. measurements may still be made for several hours after "Low battery indicator" appears before the instrument become inaccurate.
WARNING! To avoid electric shock, disconnect the test leads from any source of voltage before removing the battery cover.
"DC 9V" type 006 P (e.g. AMM-1061)
1. Open the battery cover by loosing the screws with the cross-point screwdriver
2. Carefully disconnect the old battery
3. Connect the new battery of the proper type to the power leads
4. Close the battery cover and reinstate the cover
"DC 1.5V" type AAA (e.g. AMM-1060)
1. Open the battery cover by loosing the screws with the cross-point screwdriver
2. Carefully pull out the buttery carrier and take off the old batteries
3. Plug the new batteries of the proper type in the holder and put it back
4.Close the battery cover and reinstate the cover
After completion make sure you don’t have any spare parts
If you do find spare parts, you must start all over
Does AKTAKOM AMM-1061 multimeter have auto power off function?
Yes, it does. There is Auto Power Off function in AMM-1061: the device power automatically goes off if you do not use the device within 30 minutes. If you’d like to switch the device on after it was automatically powered off press any button or use the rotary switch.
